Видео

Thanks Bro. I'm doing this for my next door neighbor and your vid is perfect! I even let the ads run full length in case you get any ad revenue.

That was very nice my mower is about four years old and getting a little noisy now I know what’s wrong with the deck no grease and the bearings. Thanks for your help.

John Deere is no ones friend.

Beautiful K5LLA Horn

Thank you.

Best video straight to the point

Thank you!

Love the accent bud, best video and very professional. Thank you Sir.🤟

On a simplicity zt2354 we don’t show battery voltage at the B terminal of the reg. Supposed to be an “inline fuse” somewhere. Can you confirm this? Can’t find one anywhere. Can a new wire just be run?

fixed my customers mower withing the first 4 minutes of watching this video!!! great job and thank you!!!

I never saw anyone use WD-40 on a Tap before. Makes a LOT of sense. I'll have to remember this. Thanks, Glen! I had a theory that adding a weep hole to know when the spindle was full, but your pre-tapped 8-32 screw for sealing is much better than what I thought of. Thanks again! I guess a 6-32 screw would work just as well, but add a littler more weep resistance to help pack the bearings. 4-40 might be OK, too. I think I'll drill both holes on the same side, and mount the two spindles with Zerk and weep screw facing outward for easy access to both. I have watched a lot of these, and I found you on my second go round today while looking for how to safely remove the bearings to be able to the use new ones on new spindles, but I think this video of yours is the best one I've seen yet. Now I also know how to get replacement bearing numbers. My spindles have two sizes each, with a larger one where the blade attaches. Mine look like your AYP, so there's plenty of height for both holes on the same side. Glen, the shaft and pulley spun faster before adding grease. I wonder if your 6-32 screw is too long and pressing on the internal spacer. Or is it the grease slowing down free spinning? I needed a Love This button for this one! Thank you so much, Glen!!!

Nice video! There’s enough spray can paint on those cars to paint another train!😱

What would cause it to make a squealing noise when I push down on the smart drive? Do you think I should replace the belt?

Thank you !!!gotter done

My problem is after I cut for a couple of hours, the engine won't start... like the battery is dead. I can charge the battery and it will start.... brand new battery. I've had it (2008 Exmark Lazer Z with the 28hp Kawasaki) at the local repair shop 3 times and they still can't fix this seemingly simple (for a trained mechanic) problem. So I've came to the conclusion that it's on me to figure it out and to find a new mechanic. Your video is just what I was looking for to assist me... THANKS!!

Great video.👍

Where do you find the fitting that goes in the weep hole?

Great video

Excellent spindle information sir

Thank you for finding your video. I bought the diagnostic kit, the interface to connect to my engine, but I have not been able to get the software. Can I contact you by email? Best regards and thank you very much in advance.

Glen, you are absolutely correct! I replaced mine last year on my Scrub Reject last year and they have already failed, and I did pump grease into them. I pulled one of my spindles apart and sure enough the bearings were sealed. The grease I pumped in did absolutely nothing for the bearing. Thank you for your expertise.

Straight to the point!

Hilarious! Thanks for uploading!

Awesome video. sure wanted that trash can bad.

Thank you for the video.

I'm surprised I'm not on here

I did this to my cub cadet just in time. Mine sounded good before but after was great. Really smooth

You can thank engineers for making it hard and making you money.

Thank you I got this on 2 mowers simple fix

Thank you

the first engine shown at very beginning of the video has a ground wire from regulator to engine bolt. The engine that you tested does not have that ground wire. Is there a difference in performance with or without?

What size is the beld ?

This is a great video. Straight to the point, clear instructions and gave me what I came here looking for. Thanks and subbed!

Very well done, you made this problem so much easier for me to understand and fix my problems. Thank you

Hoping to see this again soon.

Very Good!

Train jltv

Engineer really did a excellent job on that design

Hi. What does it mean if you've replaced the valve cover, gasket, bolts and it still leaks oil? 🤔

This video is great and makes the change easy. But I dislodged the spring and bracket when I was putting it back on, I cannot figure out how to undo it. Any tips?

If you buy a new riding lawnmower you should do this before using it 😊

Great video. Right to the point without wasting a lot of time. KOODOS !

Just finished my deck rebuild and thanks to your video, it went very well. You can use 1 1/2 by 4 inch nipple with a cap as a perfect fit your bearings. Thanks again for sharing.

Do you think a loading basket that could hold multiple cans could be custom built? I'm trying to find a solution for the place i work and this looks great but it would need to be able to hold a bunch of cans

💣💣💣🤣🤣

GM sir have a cub cadet MN-103 calls for 959-3665- and or 759 -3665 spindles i think ther roller type you ever work with these

Hi there. Thanks to your video I was able to replace my belt. Only problem is, that wasn’t the issue. It seems that the belt is too loose. I noticed some damage on the old belt and thought that might be the issue but it looks like it’s not that. I didn’t see an obvious way to tighten the tension, any idea what I could do or check to fix it? Thanks

Just one tip: if you reach under there and the belt won’t move then it’s either pinched in the pulley, off the pulley, has a stick stuck, etc. You should be able to turn the belt easily using your hands.

One of the best DIY videos I've seen -thank you, sir!

Does the diagnostic kit come nwith the software ?